3D Modelling – Page 4 – Silfer Works

OPUS KAAMOS

50og75phlg6a1 — 3D Modelling

3D Printing

Magnetic and stackable dig markers for metaldetecting

Date 4 years ago

I’m often detecting with my kid, and he usually marks the spots which he can’t dig himself. I also use markers for the “maybe” spots where the signal is questionable but I might want to check later. Now the ground is frozen, so I decided to make a bit nicer…

M8WUwSx — 3D Modelling

3D Printing

Metalworking

Metalworker’s Pacifier

Date 4 years ago

I was too cheap to buy a new chip collector, and I didn’t like the fact that I would need to use two hands to release the chips. As I had some leftover neodymium magnets from an old project, I decided that I’ll spend my Saturday night to design one…

Ho4g5deasjz91 — 3D Modelling

3D Printing

Camera for Hama Bead “pictures”

Date 4 years ago

My kid started making Hama bead “pictures”, so I made him a camera! Design time was around 3 hours, and so was print @0.15mm. A very simple print but also very liked. What can I say? I love to make useless stuff, hahah. The ready result and the “pictures”. The…

B30uvks2t6u91 — 3D Modelling

3D Printing

Magnetic blowtorch holder

Date 4 years ago

I’m continuing my mission of making my little workspace as user friendly as possible. The goal is to have all the most used tools easily accessible from my usual working position. This time I re-used my WD-40 holder design and made a blowtorch holder. 3d printed and with three magnets…

Typzryx71ut91 — 3D Modelling

3D Printing

Magnetic Roloc holder

Date 4 years ago

With a small workshop, little improvements are very noticeable. With these it’s much easier to switch disks and everything is within my arms reach. I designed two versions; one for 2” discs and another longer one for 3” discs. The final result. The holders has a place right on the…

Eillpyi5xmr91 — 3D Modelling

3D Printing

Microgolf

Date 4 years ago

What do you do you when your kid has to stay at home due to the flu and you need to work? You quickly design something that he watch being printed and then play with it! On today’s menu was Marble Minigolf. The final result. It’s trickier than you’d think….

04F99DA9 2079 4126 926B 73A5F23DB102 — 3D Modelling

3D Printing

Riot Mamas – logo

Date 4 years ago

My brother and his wife has a band called “Riot Mamas”. Me and my family were going to visit them and I decided to make a little gift to take with: a giant fridge magnet! A simple two colour design with embedded magnets.

2d2omina6ra91 — 3D Modelling

3D Printing

3D printed padlock

Date 4 years ago

This was created for my kids to play with, but in reality it was more of a design challenge than anything else. The lock is “fully functional” in the sense that it can only be opened with the key that belongs to it. The only hardware you need is a…

ZfUgwiv — 3D Modelling

3D Printing

Stand for an extra ball for a CST trackball

Date 4 years ago

I have an extra ball for my CST trackball on my desk, and I decided to design a nice 3D printed stand for it. It uses a standard skateboard bearing and you can make the ball spin for a very long time (and by that annoy your colleagues endlessly). The…

1ghyv0ntxc791 — 3D Modelling

3D Printing

WD40 can holder

Date 4 years ago

Yesterday I had the final straw when I was going to clean my welding table and the damn WD-40 can was nowhere to be found again. I went back to the house and after an hour this contraption had been designed. It took 13 hours to print and now hopefully…

Load More That's everything.

This website uses very few cookies, but cookies nevertheless. By continuing to use this site, you accept the use of cookies.